Bl c1 panasonic manual downloads. Related Posts: Armstrong astro 25b050s manual transmission Pinarello fp3 manual treadmill 6sn1123 1ab00 0aa1 manual lymphatic drainage Vtech vsmile v motion manual transfer Double horse helicopter 9101 manual dexterity Visual manual cognitive icon Technics su. Download >>Download Woggle bug manual dexterity Read Online >>Read Online Woggle bug manual dexterity make noise wogglebug review make noise wogglebug manual.

Armstrong Series S & H in-line circulating pumps are ideal for use in hydronic heating and cooling, domestic water systems, multi-stage zoning, and general industrial service. The Armstrong S & H series pumps are available with either cast iron or bronze bodies. Give us a call toll-free for help on which pump is right for your application. Body: Radially-split body can be left in the line while servicing the pump, eliminating needless disconnecting of pipes.

Oversized Shaft: ARMSTRONG circulating pumps have oversized shafts of special alloy steel, machined to exacting tolerances. Shafts have integral thrust collars, heat treated to provide long life under severe duty conditions. Centrifugal Impeller: Balanced impeller of centrifugal design ensures maximum water delivery. Positive Mechancial Seal: A tried and proven method of preventing water leakage, the well-known “ARMSEAL” construction is an often imitated feature of the ARMSTRONG circulator. Made of long-lasting, hardwearing materials, it ensures many years of noise-free, trouble-free service.

Modular Construction: Armstrong Models S-25 through S-57 and H-32 through H-54 feature the unique ARMSTRONG shaft and bearing module which fits all of these models for ease of serviceability and reduced inventory costs. Specification Item No. Specification Item No. Specification Item No. Items to be returned must be approved by Power Plus International, and may be subjected to a restocking fee Notice: Due to the uncontrollable metal costs, all prices and delivery times are subject to change on a daily basis. PPI™ and Power Plus International™, and related marks and logos displayed on the Site, are our trademarks and may not be used in any way without our prior express written permission. Nothing contained on the Site shall be construed as granting, by implication, estoppel or otherwise, any license or right to use any of our marks displayed on the Site without our prior express written permission.

All other trademarks not owned by us that appear on this Site are the property of their respective owners. *NOTE: The products described herein are not manufactured by Patterson-Kelley nor is Power Plus International in any way associated or affiliated with 'PK', Patterson-Kelley, or Harsco Corporation.

If it is 120 volts it's quite simple. First make sure to turn off the heat at the red emergency switch. This will not affect your system. Simply turn the switch back on when you are done. Remove the cover off the small box on the side of the pump.

There should be one screw holding it on. You should be feeding the pump with BX cable from the controller (Aquastat or pump relay). Older steel BX carries the ground through the cable, and the connector, but the newer, aluminum BX has a ground wire inside the cable.Remove about four inches of the BX cable from around the wires. Just bend the BX at the designated length until it breaks. Twist the cable clockwise in one hand and counter clockwise in the other.

This will open it enough for you to snip the cable,(not the wires) with dikes or tin snips. Or, you can unravel the BX from the open end. Insert a red head (anti-short) around the two or three wires and slide it into the cable leaving the four inches of wire still outside the cable. Install a 1/2' BX connector into the the round opening provided on the box.

Screw the nut onto the connector hand tight and tighten the nut by placing a flat screwdriver onto one of the nubs on the nut and tap it around with the heel of your hand or any pliers or hammer if available. Slide your wires through the connector until the cable bottoms out inside the connector. Tighten the connector set screw. Lsi Embedded Megaraid Windows 7 Driver. Now you have a black, a white, and possibly a green wire inside the box.

Strip about 3/4' of insulation off of each wire. The three wires in the box on the pump should already be stripped, but if not, strip those too. Twist the wires together using your hands or pliers.

White with white, black with black, and green with green. This ensures a good connection. Now, you can twist your orange wire nuts on to the pre-twisted wires. Use orange nuts because they are smaller and will fit into the small box better than yellow or red nuts. To ensure a proper splice, twist them until the wires start to twist in your hand.

Fold the wires into the box, install the cover onto the box making sure not to pinch the wires and turn the emergency switch back on. Answered on Nov 14, 2013. Hi, The most common problem with these circulators is that the stator gets stuck and does not turn. Sometimes you can take out the four bolts on the corners and pull the motor off. Get the stator freed up again and it will work. Make sure to turn the water off before dissassembling the pump. Hopefully you have valves do you can isolate the pump.

Also check that the impeller has not broken off the end of the shaft, that also happens sometimes. You can check the cap. With an OHM meter by switching the terminals with the test leads and the resistance should count down to zero with each switch of the leads on the terminals.if not it is bad, but replacement of the cap. May not fix the pump usually it is a secondary failure. If you can't get the pump ot work after taking it apart and making sure it turns freely then I would replace the pump.

Heatman101 Answered on Dec 29, 2009.